helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-motor system. Cat4CAD facilitates you in selecting and configuring the products, gives you the opportunity to print out extensive technical data bedding, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty class F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and higher torques in smaller sized sizes.
Multiple Input Options: Essential gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric result shafts, installation pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or via a torque arm.
Worldwide Electric motor: Multiple leads and windings for globally multi volt/Hz requirements in addition helical bevel gear reducer modular design to simply accept brakes, encoders or forced cooling.
High efficiency engine design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals on heat treated, plunge ground shafts
Shaft mounting options include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors are available in three stage high efficiency designs through 50 HP and single phase to 5 HP. We offer a selection of input and output shaft options. Additionally, you will see fixed and variable rate motors and range of ratios obtainable in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Vital dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying needs of customers, we offer an array of Helical Bevel Equipment Reducers. The technological content material of our products permits an extraordinary overall performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully found in a multitude of commercial and civil applications. They are B-Series units that offer excellent value for money and output torque/weight ratio, especially due to the fact they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with compact motor, PB-fitted for electric motor coupling with flexible joint
Casing with feet FC, flange SC and common UC
Switch on to 90 kW
Gears hardened and tempered with shaved or ground profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second decrease stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and result flanges of grey cast-iron G200 to ensure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover package, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right position helical bevel equipment motors offer ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and may be offered with single or dual extended output shafts.
Products are also available because shaft mounted or with result flanges and are available for installation horizontally or vertically. The products can also be offered with a bolt on torque reaction bracket and all variants can be found either motorised or with an input shaft assembly.
Adding to the brand new range of Ever-Power helical equipment motors this product takes benefit of our a long time of accumulated design knowledge together with the utilization of top quality materials and elements. The outcome is a series of quickness reducing geared motors offering high load transporting capacities, increased efficiency, silent running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double essential oil seals, on input and output shaft as required.
All models are dimensionally interchangeable with various other major manufacturers.
Units are manufactured and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be installed with a backstop module and reducer Units can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with small motor
Cases with feet, flange or universal
Switch on to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are constructed with high wear-resisting alloy components, specially and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, nice appearance ,and solid capacity of being overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to as high as 96% with low energy consumption, strong adaptability and is with the capacity of functioning continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal device, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.